1 – Creating a Flower
The objective of this step is to rotate and cut the edge off an ellipse, to make half a petal shape.
Create a new layer.
Use the Elliptical Selection Tool to select an elliptical area.
Choose a darkish red
colour, and fill the area with the Paint Bucket Tool.
Press Ctrl+D to remove the selection.
Press Ctrl+T to transform your shape. Drag a corner around, to rotate your shape, until it's in a position similar to the one shown in the diagram.
With the Selection
Tool, select a large part of your shape that you wish to cut off, so that
the remaining part of your shape resembles half a petal. Go back and rotate
your shape if you need to.
2 – Creating a Whole Petal
Right-click on your petal layer in the Layers list. It should be called "Layer 1".
Click Duplicate Layer.
With the duplicate layer selected click Edit > Transform > Flip Horizontal.
Choose the Move Tool,
and use the arrow keys to nudge the two half-petals around until they join
to make a whole petal. Note: pressing Shift and an arrow key nudges the object
around by 10 pixels at a time, instead of 1.
Click on the "Layer 2" layer in the Layers list. This should be your new, rotated half of the petal. Press Ctrl+E to merge this layer down, so that the petal is all on one layer.
3 – Adding Texture and Lighting to the Petal
With the merged layer selected click Filter > Noise > Add Noise. Set it to around 10%, Gaussian, and Monochromatic.
To lighten the center, set your colours back to black and white, then switch the colours, by using the little icon, or pressing "D".
Create an adjustment layer 
and choose Gradient. Set the Angle to 90° and change the Style to Reflected.
Set the Opacity of the Gradient Fill Layer to 25%, Press OK.
Ctrl+Click on Layer1 in the Layers list to select its area.
Choose the Brush Tool.
Click the drop-down box and choose the size 35 soft round brush (you may have
to change the size to match your petal size). Set the brush's colour to black
and the opacity to 20%. Apply the brush around the outside of the petal, to
create a shadowy area, as shown.
Press Ctrl+D to deselect.
Click on the "Gradient " layer in the Layers list. Press Ctrl+E to merge this layer down, so that the petal is and the gradient is on one layer.
4 – Duplicating the Petal
Right-click the petal in the Layers list, and click Duplicate Layer.
With the duplicate layer selected click Edit > Transform > Flip Vertical.
Choose the Move Tool,
and press Shift+Up arrow until the petals are arranged as shown in the diagram.
You can drag the petal around with the mouse if you like, but remember to
hold the Shift key, so the petal moves exactly vertically.
5 – Creating One Set of Petals
In the Layers list, click the eyeball next to your Background layer. This will make it disappear.
Click Layer > Merge Visible. If you try to merge the layers any other way, you'll have two sets of Blending Options (Effects) on one of the petals. That would be bad. :)
Right-click your layer in the Layers list, and click Duplicate. Press Ctrl+T to Transform your layer. Drag the corner around, but hold Shift, so it rotates in even increments. Duplicate your layer, and rotate it again. You should end up with six evenly-spaced petals, as shown in the diagram.
Click Layer > Merge Visible.
Right-click this layer in the Layers list. Give it a Drop Shadow, and press OK.
Click the eyeball next to your Background layer, to make it appear again.
6 – Finishing Touches
Duplicate this layer.
Click Ctrl+T to Transform it. Hold Shift and rotate the layer one notch.
Create a new layer.
Choose the Elliptical Selection Tool. Select a circular area in the centre of the flower. (Hold
Shift while you drag, to make your area perfectly circular.)
Choose a yellow colour,
and fill the area with the Paint Bucket Tool.
Set your colours back to black and white. (Click the icon, or press "D")
Press Ctrl+D to deselect.
Click Filter > Noise > Add Noise. Set it to around 10%, Gaussian, and Monochromatic.
Right-click this layer in the Layers list. Give it an Inner Glow.
Also add a Gradient Overlay. Set the Opacity to 60%, tick the Reverse box, and set the Style to Radial. Press OK.
Make the background disappear again, and click "Merge Visible".
7 – Creating the Shape of a Leaf
Click File > New. Choose your settings, and press OK.
As you did with the flower, create a green ellipse shape, rotate it, and delete all but a piece at the edge. Duplicate that piece, flip it, and merge them into one layer.
See Step 1 if you've forgotten how to do this.
8 – Adding Texture and a Gradient
Click Filter > Noise > Add Noise. Set it to around 10%, Gaussian, and Monochromatic.
Ctrl+Click your leaf layer in the Layers list.
Create a new layer.
Change its Mode from Normal to Overlay.
Choose the Gradient Tool and apply it from left to right, across your selected area.
9 – Adding Veins to the Leaf
Create a new layer.
Choose the Brush Tool.
Click the drop-down box and choose the size 9 blurry brush. Set the brush's
Opacity to 20%. Draw a slightly wavy line down the centre of your leaf.
Choose a size 5 blurry brush, and then paint in the side veins.
Create a new layer.
Select the size 17
blurry brush. Paint two rough, white lines—one down each side of the leaf.
Change your colour to black, and paint down the main vein, and around the
edges of the leaf.
Turn the background layer off, and click Layer > Merge Visible.
10 – Creating Repeating Elements
You will need to create four new images here. These images will repeat along the top, bottom, and sides of your page. The image shown above is something like what your top image should look like.
Choose the Move Tool,
and drag flowers and leaves from your other images.
Use Ctrl+T to resize the flower. Hold shift while doing this, to stop the flower distorting.
For each of this images,
|
|
||
|
Left Repeater
|
Picture |
Right Repeater |
|
|
||
Place a Picture into your new
flower border and save.
Border
Exercise - Using the techniques above design
and create your own border. Add a
picture and save.